Wraps by car

Mitsubishi 500 wrap

This page covers the Mitsubishi 500 wrap, a vinyl wrap job on a small early Japanese sedan. The catalog lists one generation of the Mitsubishi 500, produced from 1960 to 1962. A full wrap of this body takes about 34 ft (10.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 44 ft (13.5 m).

1generations10.5 mof film for a full wrap

Mitsubishi 500, first generation, factory photo
Mitsubishi 500, first generation. Factory color shown.

Mitsubishi 500 wrap colors and ideas

  • Mitsubishi 500 black wrap
  • Mitsubishi 500 white wrap
  • Mitsubishi 500 gray wrap
  • Mitsubishi 500 silver wrap
  • Mitsubishi 500 red wrap
  • Mitsubishi 500 blue wrap
  • Mitsubishi 500 green wrap
  • Mitsubishi 500 yellow wrap
  • Mitsubishi 500 orange wrap
  • Mitsubishi 500 purple wrap
  • Mitsubishi 500 pink wrap
  • Mitsubishi 500 teal wrap
  • Mitsubishi 500 brown wrap
  • Mitsubishi 500 gold wrap
  • Mitsubishi 500 chrome wrap
  • Mitsubishi 500 color shift wrap
  • Mitsubishi 500 carbon fiber wrap
  • Mitsubishi 500 camo and patterned wrap

How much vinyl to wrap a Mitsubishi 500

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1960–1962sedan (2 doors)123.6 in (3,140 mm)about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m)

Mitsubishi 500 wrap cost factors

Mitsubishi 500 wrap cost depends on the size of the car and the amount of surface preparation. At 123.6 in (3,140 mm) long, it uses less film than a modern compact, so material cost is lower. The main cost driver is the condition of the paint on a car from 1960 to 1962. Any rust repair, dent filling, or paint stabilization adds labor before the wrap can be installed.

  • Film for a full wrap: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).
  • Body: sedan (2 doors).
  • Two long side doors: each door is one large piece of film.

Mitsubishi 500 wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi 500, first generation, factory photo
Factory color shown

1960–1962 Mitsubishi 500 sedan (first generation)

1960–1962sedan (2 doors)123.6 in (3,140 mm)

The first generation Mitsubishi 500 was built from 1960 to 1962 as a two-door sedan. Paint age is a key factor on a car of these years because panels may be original or repainted. Before a full wrap, we always do a test spot to check how the film adheres to the existing paint. If the test spot shows poor bond, the surface needs correction or priming first.

Two long side doors: each door is one large piece of film.

Film: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).

Roof, hood, chrome delete and PPF on a Mitsubishi 500

A Mitsubishi 500 chrome delete covers window trim and badges with black film for a more uniform look. A partial wrap can be as small as the roof, hood, or mirror caps, which suits the car's compact panels. Paint protection film (PPF) is clear film on the front end to guard against stone chips. Any of these jobs uses less material than a full wrap and still changes the car's appearance.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mitsubishi 500: body, cut-outs and film

A Mitsubishi 500 vinyl wrap involves one simple body style: a two-door sedan. The car measures 123.6 in (3,140 mm) long, so the panels are small and the total film area is modest. Its short roof and short hood reduce the amount of material compared to larger sedans. The two long side doors are each one large piece of film, which keeps the number of seams low.

Mitsubishi 500 wrap ideas begin with its clean surfaces and limited trim. The side doors are large enough to carry a design without piecing, but the window frames and handles stay unwrapped and require careful cutting. Badges and small trim pieces can be removed for a cleaner edge, or left in place with precise relief cuts. The front and rear bumpers are separate parts that can be wrapped in a contrasting color.

How much vinyl to wrap a Mitsubishi 500 depends on how you order film. Only one generation was produced, so every example uses the same dimensions. Counting on about 34 ft (10.5 m) of 60-inch (1.52 m) film is enough for a full color change wrap. If you add chrome or a patterned film and need to match direction, you may need about 44 ft (13.5 m).

Questions about wrapping a Mitsubishi 500

How much vinyl does it take to wrap a Mitsubishi 500?

About 34 ft (10.5 m) of 60-inch (1.52 m) cast film is enough to wrap a Mitsubishi 500. That figure covers the only body style, the two-door sedan. If you choose chrome or patterned film, you may need about 44 ft (13.5 m) to account for pattern matching. The estimate assumes no major repairs or re-wrapping of failed panels.

Can I wrap only the hood or the roof of a Mitsubishi 500?

Yes, you can wrap only the hood or the roof of a Mitsubishi 500. The partial wrap options for this car include the roof, hood, and mirror caps. A chrome delete covers window trim and badges with black film. These smaller jobs use less material and still give the car a changed look.

Is a Mitsubishi 500 hard to wrap?

Yes, a Mitsubishi 500 has some points that add work during a wrap. The two long side doors are each one large piece of film, which requires careful alignment to avoid wrinkles. The car is small at 123.6 in (3,140 mm) long, so bumpers and trim are close together and need tight cutting. The age of the car means the paint may need correction before film will stick well.

How many generations of the Mitsubishi 500 does this page cover?

This page covers one generation of the Mitsubishi 500. That generation was produced from 1960 to 1962 as a two-door sedan. There were no other generations of this model.