Wraps by car

Mitsubishi Celeste wrap

The Mitsubishi Celeste wrap page covers the first generation produced from 1975 to 1981. A full vinyl wrap of its hatchback body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly another 10 ft (3 m) for a total around 56 ft (17 m).

1generations14 mof film for a full wrap

Mitsubishi Celeste, first generation, factory photo
Mitsubishi Celeste, first generation. Factory color shown.

Mitsubishi Celeste wrap colors and ideas

  • Celeste black wrap
  • Celeste white wrap
  • Celeste gray wrap
  • Celeste silver wrap
  • Celeste red wrap
  • Celeste blue wrap
  • Celeste green wrap
  • Celeste yellow wrap
  • Celeste orange wrap
  • Celeste purple wrap
  • Celeste pink wrap
  • Celeste teal wrap
  • Celeste brown wrap
  • Celeste gold wrap
  • Celeste chrome wrap
  • Celeste color shift wrap
  • Celeste carbon fiber wrap
  • Celeste camo and patterned wrap

How much vinyl to wrap a Mitsubishi Celeste

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1975–1981hatchback (3 doors)155.9 in (3,960 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Celeste wrap cost factors

Celeste wrap cost is driven by the film used, the amount of bodywork preparation, and the labor to handle a car of this age. The hatchback takes about 46 ft (14 m) of 60-inch (1.52 m) film, with more for chrome or patterned options. A car from 1975–1981 may need deep cleaning, paint correction, or rust repair before the film goes on. Removing trim and wrapping the tailgate around the glass adds time to the job.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Celeste wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi Celeste, first generation, factory photo
Factory color shown

1975–1981 Celeste hatchback (first generation)

1975–1981hatchback (3 doors)155.9 in (3,960 mm)

The first generation Mitsubishi Celeste was built from 1975 to 1981 as a compact hatchback with three doors. Paint on a car of these years may be original or repainted, so a test spot comes before a full wrap. A small film sample shows whether the surface will hold and helps avoid lifting later. The film estimate assumes the body is clean and free of deep damage.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Celeste

Partial wrap on a Celeste can cover the roof, hood, or mirror caps without doing the whole car. Celeste chrome delete is done on the window trim and badges by covering the bright parts with black film. Paint protection film (PPF) is a clear film applied to the front end to guard the hood and bumper from stone chips. These smaller jobs use less film and leave the rest of the original color showing.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mitsubishi Celeste: body, cut-outs and film

A Mitsubishi Celeste vinyl wrap is planned around a compact hatchback with three doors and an overall length of 155.9 in (3,960 mm). The single body style has two long doors, each covered as one large piece of film. The rear side panels are short, so less film goes into the quarter area than on a four-door car. The tailgate includes the rear glass, which keeps the film area tighter around the window edge.

Celeste wrap ideas start with the two long doors, each installed as a single large panel without seams. The tailgate holds the rear glass, so the film ends at the edge of the glass and leaves the window bare. Mirror caps, door handles, and badges come off or are cut around for cleaner edges. The front and rear bumpers are wrapped while mounted to keep the curves aligned.

How much vinyl to wrap a Celeste depends on the film type and the one body style offered from 1975 to 1981. The hatchback needs about 46 ft (14 m) of 60-inch (1.52 m) cast film for a standard color change. Chrome or patterned film requires about 56 ft (17 m) because patterns must match across the body. There is only one generation in this catalog, so the figures do not change between years.

Questions about wrapping a Mitsubishi Celeste

How much vinyl does it take to wrap a Mitsubishi Celeste?

A Mitsubishi Celeste takes about 46 ft (14 m) of 60-inch (1.52 m) cast film for a full wrap of the hatchback body. If you use chrome or patterned film, count about 56 ft (17 m) because the pattern needs extra material for matching.

Can I wrap only the hood or the roof of a Celeste?

Yes, you can wrap only the hood or the roof of a Celeste. These are listed as partial wrap options along with mirror caps, chrome delete on window trim and badges, and clear paint protection film on the front end.

Is a Celeste hard to wrap?

A Celeste adds work in two ways: the tailgate includes the rear glass, so the film ends at the glass edge and needs careful trimming. The two long side doors are each wrapped as one large piece, which requires a steady hand to avoid wrinkles. At 155.9 in (3,960 mm), it is a compact car, but the age of the paint may also mean more preparation.

How many generations of the Celeste does this page cover?

This page covers one generation of the Mitsubishi Celeste, the first generation from 1975 to 1981. The catalog lists only that generation with a hatchback body style and the film figures for a full wrap.