Wraps by car

Mitsubishi Dingo wrap

A Mitsubishi Dingo wrap is a color change or protection film for this tall five-door minivan. The catalog covers one generation of the Dingo, produced from 1998 to 2003. A full wrap of the newest body takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. A vinyl wrap is cut to the panels and finished around the edges of this body.

1generations13.5 mof film for a full wrap

Mitsubishi Dingo, first generation, factory photo
Mitsubishi Dingo, first generation. Factory color shown.

Mitsubishi Dingo wrap colors and ideas

  • Dingo black wrap
  • Dingo white wrap
  • Dingo gray wrap
  • Dingo silver wrap
  • Dingo red wrap
  • Dingo blue wrap
  • Dingo green wrap
  • Dingo yellow wrap
  • Dingo orange wrap
  • Dingo purple wrap
  • Dingo pink wrap
  • Dingo teal wrap
  • Dingo brown wrap
  • Dingo gold wrap
  • Dingo chrome wrap
  • Dingo color shift wrap
  • Dingo carbon fiber wrap
  • Dingo camo and patterned wrap

How much vinyl to wrap a Mitsubishi Dingo

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1998–2003hatchback (5 doors)153.0 in (3,885 mm)about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Dingo wrap cost factors

Dingo wrap cost depends on the job size, the film type, and the condition of the panels. A full wrap of this 153.0 in (3,885 mm) car needs about 44 ft (13.5 m) of 60-inch film, so more film and more hours add to the cost. Partial wraps and chrome delete use less material and less labor. On a car of these years the paint may need cleaning or repair before the film goes on, which also changes the cost.

  • Film for a full wrap: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: hatchback (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Dingo wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi Dingo, first generation, factory photo
Factory color shown

1998–2003 Dingo hatchback (first generation)

1998–2003hatchback (5 doors)153.0 in (3,885 mm)

The first generation Mitsubishi Dingo, made from 1998 to 2003, is the only body covered here. Paint age on a car of these years means the panels may be original or repainted, and a test spot comes before a full wrap. A test spot checks that the film sticks to the old paint and that the paint will not lift when the film is removed. If a panel has been repainted, the wrap may need more time and a different primer.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Dingo

A partial wrap on a Mitsubishi Dingo covers the roof, the hood, or the mirror caps. Dingo chrome delete is a smaller job: the window trim and the badges are covered with black film. Paint protection film (PPF) is a clear film on the front end, from the bumper to the leading edge of the hood. Partial wrap uses less film than a full wrap, so it is a smaller job and a smaller film bill.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mitsubishi Dingo: body, cut-outs and film

A Mitsubishi Dingo vinyl wrap works with one body style, a five-door hatchback with a tall minivan shape. The car is 153.0 in (3,885 mm) long, so a full wrap uses about 44 ft (13.5 m) of 60-inch film. The flat sides and large roof make for long, simple panel cuts. The tall rear corners and the tailgate need careful work so the film follows the body lines.

Dingo wrap ideas start with the tailgate, where the film ends at the edge of the rear glass. The rear glass is set into the tailgate, so the wrap does not go over the glass itself. Door handles, the antenna base, and the side moldings are removed or cut around for a clean install. The badges come off for a smooth vinyl finish and can go back on after the wrap.

How much vinyl to wrap a Dingo is based on one generation, so the film amount stays the same from 1998 to 2003. A color change wrap needs about 44 ft (13.5 m) of 60-inch cast film. A chrome or patterned film uses more, about 51 ft (15.5 m), because the pattern has to be matched. The same body is used for all years, so there is no change in the panel count or the film size.

Questions about wrapping a Mitsubishi Dingo

How much vinyl does it take to wrap a Mitsubishi Dingo?

A full wrap of a Mitsubishi Dingo takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. The figure is for a color change wrap on the first generation body, which is the only one in this catalog. A chrome or patterned film uses more, about 51 ft (15.5 m). The estimate is for the whole body, from the front bumper to the tailgate.

Can I wrap only the hood or the roof of a Dingo?

Yes, you can wrap only the hood or the roof of a Dingo. A partial wrap on this car covers the roof, the hood, or the mirror caps. The roof is a large flat panel, so it is one of the simpler parts to film on this tall minivan. The hood is also a single panel with easy edges.

Is a Dingo hard to wrap?

A Dingo is not hard to wrap, but the tailgate adds a step. The rear glass is set into the tailgate, so the film has to end at the edge of the glass. The tall body and the simple sides make the rest of the car straightforward. The 153.0 in (3,885 mm) length means there are no extra long panels that need two people.

How many generations of the Dingo does this page cover?

This page covers one generation of the Mitsubishi Dingo, made from 1998 to 2003. The catalog has only one body for this model, a five-door hatchback minivan. There are no other generations of the Dingo listed, so the film amount and the wrap facts are the same for all years.