Wraps by car

Mitsubishi Pajero Junior wrap

This page covers the Mitsubishi Pajero Junior wrap, the compact SUV built from 1995 to 1998. The catalog lists one generation of this three-door model. A full vinyl wrap of the Pajero Junior takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film.

1generations14.5 mof film for a full wrap

Mitsubishi Pajero Junior, first generation, factory photo
Mitsubishi Pajero Junior, first generation. Factory color shown.

Mitsubishi Pajero Junior wrap colors and ideas

  • Pajero Junior black wrap
  • Pajero Junior white wrap
  • Pajero Junior gray wrap
  • Pajero Junior silver wrap
  • Pajero Junior red wrap
  • Pajero Junior blue wrap
  • Pajero Junior green wrap
  • Pajero Junior yellow wrap
  • Pajero Junior orange wrap
  • Pajero Junior purple wrap
  • Pajero Junior pink wrap
  • Pajero Junior teal wrap
  • Pajero Junior brown wrap
  • Pajero Junior gold wrap
  • Pajero Junior chrome wrap
  • Pajero Junior color shift wrap
  • Pajero Junior carbon fiber wrap
  • Pajero Junior camo and patterned wrap

How much vinyl to wrap a Mitsubishi Pajero Junior

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1995–1998SUV (3 doors)137.8 in (3,500 mm)about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

Pajero Junior wrap cost factors

Pajero Junior wrap cost depends on the amount of film and the choice of finish. A chrome or patterned wrap needs about 54 ft (16.5 m) of film, while a standard color takes about 48 ft (14.5 m). Labor is affected by the tailgate glass cut-out and the door handle removal. The car's short 137.8 in (3,500 mm) length keeps the total film area moderate.

  • Film for a full wrap: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: SUV (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Pajero Junior wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi Pajero Junior, first generation, factory photo
Factory color shown

1995–1998 Pajero Junior SUV (first generation)

1995–1998SUV (3 doors)137.8 in (3,500 mm)

The first generation Mitsubishi Pajero Junior was produced from 1995 to 1998 as a three-door SUV. Paint on a car of these years may be original or repainted, so a test spot should be done before a full wrap. The body code H57A identifies this generation. Its 137.8 in (3,500 mm) length and tall panels make film application direct.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on a Pajero Junior

Partial wrap options for the Mitsubishi Pajero Junior include the roof, hood, and mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end. These smaller jobs change the look without a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mitsubishi Pajero Junior: body, cut-outs and film

A Mitsubishi Pajero Junior vinyl wrap uses the car's small size and three-door layout to keep panel count down. At 137.8 in (3,500 mm) long, the sides break into just a few large pieces. The tall, flat SUV panels let film lay down without deep stretches. The wrap can be planned as one clean, continuous job across the body.

For Pajero Junior wrap ideas, the main cut-outs are the tailgate glass and the door handles. The tailgate has the rear glass built in, so the film ends at the glass edge. Each of the two long side doors can be wrapped as one large piece. Door handles and mirrors come off for a cleaner edge.

To figure how much vinyl to wrap a Pajero Junior, a full color change uses about 48 ft (14.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or a patterned film, budget about 54 ft (16.5 m) because the pattern must be matched. The catalog has one generation, so figures stay the same for all years of this model. Extra film is also needed for cut-outs and mistakes.

Questions about wrapping a Mitsubishi Pajero Junior

How much vinyl does it take to wrap a Mitsubishi Pajero Junior?

A Mitsubishi Pajero Junior takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film for a full wrap. That figure covers the standard color change on the three-door SUV body. If you use chrome or patterned film, the amount rises to about 54 ft (16.5 m).

Can I wrap only the hood or the roof of a Pajero Junior?

Yes, you can wrap only the hood or the roof of a Pajero Junior. Partial wrap jobs on this model often include the roof, hood, and mirror caps. A chrome delete on the window trim and badges is another way to change part of the car. Paint protection film is also offered as a clear front-end option.

Is a Pajero Junior hard to wrap?

A Pajero Junior is not especially hard to wrap, but two areas need care. The tailgate has the rear glass in it, so the film ends at the edge of the glass. Each of the two long side doors is one large piece, which takes a steady hand to align. The car's short 137.8 in (3,500 mm) length means fewer seams overall.

How many generations of the Pajero Junior does this page cover?

This page covers one generation of the Mitsubishi Pajero Junior. The catalog lists only the first generation, produced from 1995 to 1998. That generation is the three-door SUV with body code H57A.