Wraps by car

Mitsubishi Pajero Pinin wrap

This page covers the Mitsubishi Pajero Pinin wrap from 1998 to 2005, the only generation in our catalog. A full vinyl wrap on the newest body takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. The films we use are cast for a long, even fit.

1generations16.5 mof film for a full wrap

Mitsubishi Pajero Pinin, first generation, factory photo
Mitsubishi Pajero Pinin, first generation. Factory color shown.

Mitsubishi Pajero Pinin wrap colors and ideas

  • Pajero Pinin black wrap
  • Pajero Pinin white wrap
  • Pajero Pinin gray wrap
  • Pajero Pinin silver wrap
  • Pajero Pinin red wrap
  • Pajero Pinin blue wrap
  • Pajero Pinin green wrap
  • Pajero Pinin yellow wrap
  • Pajero Pinin orange wrap
  • Pajero Pinin purple wrap
  • Pajero Pinin pink wrap
  • Pajero Pinin teal wrap
  • Pajero Pinin brown wrap
  • Pajero Pinin gold wrap
  • Pajero Pinin chrome wrap
  • Pajero Pinin color shift wrap
  • Pajero Pinin carbon fiber wrap
  • Pajero Pinin camo and patterned wrap

How much vinyl to wrap a Mitsubishi Pajero Pinin

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1998–2005SUV (3 or 5 doors)147.0 in (3,735 mm) to 158.9 in (4,035 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Pajero Pinin wrap cost factors

The Pajero Pinin wrap cost is set by the film, the size and the number of cut-outs. A full wrap on a 5-door body uses about 54 ft (16.5 m) of 60-inch (1.52 m) film, so the film area drives the price. A 3-door body uses less material because the roof is shorter than on a 5-door. Chrome or patterned film brings the estimate to about 61 ft (18.5 m), which also raises the price.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: SUV (3 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Pajero Pinin wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi Pajero Pinin, first generation, factory photo
Factory color shown

1998–2005 Pajero Pinin SUV (first generation)

1998–2005SUV (3 or 5 doors)147.0 in (3,735 mm) to 158.9 in (4,035 mm)

The first generation of the Mitsubishi Pajero Pinin ran from 1998 to 2005 for this catalog. On a car of these years, panels may be original or repainted, so the installer does a test spot before a full wrap. That step shows whether old paint or clear coat will lift when the vinyl is removed. It also tells us if the surface needs more cleaning before the film goes on.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Pajero Pinin

A partial wrap on the Pajero Pinin covers smaller areas such as the roof, hood and mirror caps. A chrome delete replaces the bright window trim and badges with black film. Paint protection film (PPF) is a clear film that goes on the front end to stop stone chips. These jobs use far less material than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mitsubishi Pajero Pinin: body, cut-outs and film

The Mitsubishi Pajero Pinin vinyl wrap has to follow an SUV body that was sold with 3 or 5 doors. The overall length runs from 147.0 in (3,735 mm) to 158.9 in (4,035 mm) across these two styles. A 5-door body adds more doors and a longer roof, which means more film than a 3-door. For a full wrap, the installer cuts panels to match both door counts and the boxy rear shape.

Pajero Pinin wrap ideas often start with the tailgate and the rear glass that sits in it. The vinyl is terminated at the edge of the glass so the film lies flat and does not peel. For the badges on the tailgate, a trim tool removes them and they are refitted after the film is down. Door handles and mirror caps are other parts that come off for a clean wrap.

If you need to know how much vinyl to wrap a Pajero Pinin, the catalog lists one body, so the figure stays the same from 1998 to 2005. The estimate of about 54 ft (16.5 m) of 60-inch (1.52 m) cast film matches the longest body at 158.9 in (4,035 mm). If you choose a chrome or patterned film, the waste rises to about 61 ft (18.5 m) of the same width. The installer will still add a small margin for mistakes on the rear corners.

Questions about wrapping a Mitsubishi Pajero Pinin

How much vinyl does it take to wrap a Mitsubishi Pajero Pinin?

A full wrap on a Mitsubishi Pajero Pinin takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. That figure comes from the newest body in the catalog, the 5-door SUV up to 158.9 in (4,035 mm) long. If you choose a chrome or patterned film, the estimate rises to about 61 ft (18.5 m) of the same width.

Can I wrap only the hood or the roof of a Pajero Pinin?

Yes, you can wrap only the hood or the roof of a Pajero Pinin. These are standard partial wrap jobs along with mirror caps. The installer uses the same cast film designed for full wraps but much less of it.

Is a Pajero Pinin hard to wrap?

A Pajero Pinin is not the hardest car to wrap, but the tailgate and the glass inside it add work. The installer must end the film at the edge of the rear glass, which takes more time than a flat panel. The boxy rear and the door cut-outs on 5-door bodies also mean more trimming.

How many generations of the Pajero Pinin does this page cover?

This page covers one generation of the Mitsubishi Pajero Pinin, from 1998 to 2005. The catalog lists only that first generation, with 3-door and 5-door SUV bodies. All the film figures and wrap notes on this page are for that single generation.