Wraps by car

Peugeot 1007 wrap

This page covers the Peugeot 1007, a subcompact hatchback produced from 2005 to 2009. The Peugeot 1007 wrap section details the vinyl wrap needs of this single-generation model. A full wrap of the Peugeot 1007 body takes about 49 ft (15 m) of 60-inch (1.52 m) cast film.

1generations15 mof film for a full wrap

Peugeot 1007, first generation, factory photo
Peugeot 1007, first generation. Factory color shown.

Peugeot 1007 wrap colors and ideas

  • Peugeot 1007 black wrap
  • Peugeot 1007 white wrap
  • Peugeot 1007 gray wrap
  • Peugeot 1007 silver wrap
  • Peugeot 1007 red wrap
  • Peugeot 1007 blue wrap
  • Peugeot 1007 green wrap
  • Peugeot 1007 yellow wrap
  • Peugeot 1007 orange wrap
  • Peugeot 1007 purple wrap
  • Peugeot 1007 pink wrap
  • Peugeot 1007 teal wrap
  • Peugeot 1007 brown wrap
  • Peugeot 1007 gold wrap
  • Peugeot 1007 chrome wrap
  • Peugeot 1007 color shift wrap
  • Peugeot 1007 carbon fiber wrap
  • Peugeot 1007 camo and patterned wrap

How much vinyl to wrap a Peugeot 1007

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2005–2009hatchback (3 doors)146.9 in (3,731 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)

Peugeot 1007 wrap cost factors

The Peugeot 1007 wrap cost depends on film type, amount, and labor. The car needs about 49 ft (15 m) of cast film for a full color change. Chrome or patterned film increases material to about 57 ft (17.5 m). Custom cut-outs around the tailgate glass and door handles add time.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Peugeot 1007 wraps by generation

Swipe sideways. Tap a card for the full description.

Peugeot 1007, first generation, factory photo
Factory color shown

2005–2009 Peugeot 1007 hatchback (first generation)

2005–2009hatchback (3 doors)146.9 in (3,731 mm)

The first generation Peugeot 1007 was built from 2005 to 2009. Paint on a car of these years may be original or repainted, so a test spot comes before a full wrap. Aging panels can hold film differently, especially on the roof and hood edges.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Roof, hood, chrome delete and PPF on a Peugeot 1007

A partial wrap on the Peugeot 1007 can cover the roof, hood, or mirror caps. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) adds a clear layer to the front end. These jobs use less material than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Peugeot 1007: body, cut-outs and film

The Peugeot 1007 vinyl wrap is a compact job on a three-door hatchback. The body length is 146.9 in (3,731 mm), so a standard roll width covers most panels with little waste. The two long side doors each take one large piece of film, which speeds up installation.

Peugeot 1007 wrap ideas start with the tailgate, where the rear glass sits in the panel. The film must end at the edge of the glass for a clean finish. The long side doors are wrapped as single pieces without seams. Door handles and badges need removal or careful cut-outs.

How much vinyl to wrap a Peugeot 1007 depends on the film type. The estimate for this single-generation model is about 49 ft (15 m) of 60-inch (1.52 m) cast film. Chrome or patterned film takes more material, about 57 ft (17.5 m). Buy extra for mistakes and panel edges.

Questions about wrapping a Peugeot 1007

How much vinyl does it take to wrap a Peugeot 1007?

A full Peugeot 1007 wrap takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. That figure covers the entire hatchback body of the first generation. For chrome or patterned film, plan on about 57 ft (17.5 m).

Can I wrap only the hood or the roof of a Peugeot 1007?

Yes, you can wrap only the hood or the roof of a Peugeot 1007. Partial wrap options include the roof, hood, and mirror caps. Chrome delete covers the window trim and badges with black film.

Is a Peugeot 1007 hard to wrap?

The Peugeot 1007 has a tailgate with rear glass in the panel, so the film must end at the glass edge. The two long side doors are each one large piece of film, which needs careful alignment. The car's small size makes some areas tighter to work around.

How many generations of the Peugeot 1007 does this page cover?

This page covers one generation of the Peugeot 1007, produced from 2005 to 2009.