Wraps by car

Peugeot 3008 wrap

The Peugeot 3008 wrap page covers all three generations of this SUV, from the first body launched in 2008 to the current model. The newest body, produced from 2023 onward, needs about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full color change wrap. Chrome or patterned film for the same body takes about 69 ft (21 m) because the pattern must be matched. These figures give a starting point for planning a wrap on any Peugeot 3008.

3generations18.5 mof film for a full wrap

Peugeot 3008, third generation, factory photo
Peugeot 3008, third generation. Factory color shown.

Peugeot 3008 wrap colors and ideas

  • Peugeot 3008 black wrap
  • Peugeot 3008 white wrap
  • Peugeot 3008 gray wrap
  • Peugeot 3008 silver wrap
  • Peugeot 3008 red wrap
  • Peugeot 3008 blue wrap
  • Peugeot 3008 green wrap
  • Peugeot 3008 yellow wrap
  • Peugeot 3008 orange wrap
  • Peugeot 3008 purple wrap
  • Peugeot 3008 pink wrap
  • Peugeot 3008 teal wrap
  • Peugeot 3008 brown wrap
  • Peugeot 3008 gold wrap
  • Peugeot 3008 chrome wrap
  • Peugeot 3008 color shift wrap
  • Peugeot 3008 carbon fiber wrap
  • Peugeot 3008 camo and patterned wrap

How much vinyl to wrap a Peugeot 3008

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2023–nowSUV (5 doors)178.8 in (4,542 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)
2016–2024SUV (5 doors)175.1 in (4,447 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)
2008–2016SUV (5 doors)171.9 in (4,365 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

Peugeot 3008 wrap cost factors

A Peugeot 3008 wrap cost depends on the size of the body, the film type, and the number of cut-outs. The newest body is 178.8 in (4,542 mm) long and uses up to 69 ft (21 m) of film, which means more material and labor than a first generation. Every trim has parking sensors, and some trims have cameras and roof rails that add time to the installation. A chrome delete or partial wrap costs less than a full color change because it uses less film and fewer panels.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: SUV (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Some trims have a panoramic glass roof: glass is not wrapped, and the film ends at the roof rails.
  • Every trim has roof rails: they come off before the roof is wrapped, or the film is cut along them.
  • Every trim has parking sensors in the bumpers: the film is cut around each sensor.
  • Every trim has cameras in the body: the film is cut around each lens.
  • Every trim has fog lamps in the front bumper: cut-outs in the bumper film.
  • Plug-in and electric versions: the charge port door is wrapped as a small piece of its own.

Peugeot 3008 wraps by generation

Swipe sideways. Tap a card for the full description.

Peugeot 3008, third generation, factory photo
Factory color shown

2023–now Peugeot 3008 SUV (third generation)

2023–nowSUV (5 doors)178.8 in (4,542 mm)

The third generation Peugeot 3008, built from 2023 onward, has a glass roof on some trims that is not wrapped, so the roof stays dark whatever the color of the film. The film ends at the roof rails, which are present on every trim and come off before the roof is wrapped. This body is the longest at 178.8 in (4,542 mm) and needs about 61 ft (18.5 m) of standard cast film for a full wrap. Chrome or patterned film for this generation takes about 69 ft (21 m) because of the larger panels.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Some trims have a panoramic glass roof: glass is not wrapped, and the film ends at the roof rails.

Every trim has roof rails: they come off before the roof is wrapped, or the film is cut along them.

Every trim has parking sensors in the bumpers: the film is cut around each sensor.

Every trim has cameras in the body: the film is cut around each lens.

Every trim has fog lamps in the front bumper: cut-outs in the bumper film.

Plug-in and electric versions: the charge port door is wrapped as a small piece of its own.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Peugeot 3008, second generation, factory photo
Factory color shown

2016–2024 Peugeot 3008 SUV (second generation)

2016–2024SUV (5 doors)175.1 in (4,447 mm)

The second generation Peugeot 3008 covers the body built from 2016 to 2024, and its years overlap with the newer body from 2023 to 2024, so the owner of a car from those years should check which body it is. This generation often has a restyled front end from 2020, but the basic shape stays the same. It is 175.1 in (4,447 mm) long and uses about 61 ft (18.5 m) of standard cast film for a full wrap. Some trims have a factory two-tone body, and the wrap either keeps that split or covers it.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Some trims have a panoramic glass roof: glass is not wrapped, and the film ends at the roof rails.

Some trims have a sunroof: the roof film is cut around its opening.

Some trims have a two-tone body from the factory: the roof is a second color, and the wrap either keeps that split or covers it.

Some trims have roof rails: they come off before the roof is wrapped, or the film is cut along them.

Some trims have bright decorative moldings: they stay bright next to the film unless a chrome delete covers them.

Every trim has parking sensors in the bumpers: the film is cut around each sensor.

Some trims have cameras in the body: the film is cut around each lens.

Some trims have fog lamps in the front bumper: cut-outs in the bumper film.

Plug-in and electric versions: the charge port door is wrapped as a small piece of its own.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Peugeot 3008, first generation, factory photo
Factory color shown

2008–2016 Peugeot 3008 SUV (first generation)

2008–2016SUV (5 doors)171.9 in (4,365 mm)

The first generation Peugeot 3008 from 2008 to 2016 often has older paint, and panels may be original or repainted, so a test spot comes before a full wrap. This test shows whether the film will adhere properly to the old paint without pulling it when removed. The body is 171.9 in (4,365 mm) long and uses about 59 ft (18 m) of standard cast film for a full wrap. For chrome or patterned film, this generation uses about 67 ft (20.5 m) because of the smaller size.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Some trims have a panoramic glass roof: glass is not wrapped, and the film ends at the roof rails.

Some trims have a sunroof: the roof film is cut around its opening.

Some trims have bright decorative moldings: they stay bright next to the film unless a chrome delete covers them.

Some trims have parking sensors in the bumpers: the film is cut around each sensor.

Some trims have fog lamps in the front bumper: cut-outs in the bumper film.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a Peugeot 3008

A partial wrap on a Peugeot 3008 covers the hood, mirror caps, or roof on cars without the glass panel. Chrome delete covers the window trim and badges with black film, which works well on every generation. Paint protection film (PPF) is clear film applied to the front end to guard against stone chips. These jobs use much less film than a full wrap and can be done without wrapping the whole body.

  • Partial wrap: hood, mirror caps, roof on cars without the glass panel.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Peugeot 3008: body, cut-outs and film

The Peugeot 3008 vinyl wrap is made easier by its five-door SUV shape, which avoids long roof panels or complex rear bodywork. The third generation is 178.8 in (4,542 mm) long, the second generation 175.1 in (4,447 mm), and the first generation 171.9 in (4,365 mm). All bodies have a tailgate with the rear glass in it, so the film ends at the edge of the glass. The roof area is manageable because every generation has a conventional SUV profile.

Peugeot 3008 wrap ideas start with the parts that need cut-outs or removal. Every trim level has parking sensors in the bumpers, so the film is cut around each sensor circle. Some trims have cameras in the body, and the film is cut around each lens to keep the view clear. Roof rails come off before the roof is wrapped, or the film is cut along them for a clean edge. The charge port door on plug-in and electric versions is wrapped as a small separate piece.

How much vinyl to wrap a Peugeot 3008 depends on which generation you own. The newest body from 2023 onward and the second generation from 2016 to 2024 both use about 61 ft (18.5 m) of standard cast film. The first generation from 2008 to 2016 is slightly smaller and uses about 59 ft (18 m) of the same film. For chrome or patterned film, the second and first generations both need about 67 ft (20.5 m), while the newest body needs about 69 ft (21 m).

Questions about wrapping a Peugeot 3008

How much vinyl does it take to wrap a Peugeot 3008?

It takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film to wrap the newest Peugeot 3008 body from 2023 onward. This figure covers a full color change wrap on all painted panels, with the film ending at the edge of the glass. If you use chrome or patterned film, the total rises to about 69 ft (21 m) because the pattern must be matched at the seams. Older generations use slightly less film due to their smaller size.

Can the roof of a Peugeot 3008 be wrapped?

Yes, the roof of a Peugeot 3008 can be wrapped unless your car has the panoramic glass roof found on some trims. The glass panel is not wrapped, so the film ends at the roof rails or the edge of the glass. If your car has roof rails, they come off before the roof is wrapped, or the film is cut along them. A roof wrap in black or another color is a common way to change the look without wrapping the whole car.

Can I wrap only the hood or the roof of a Peugeot 3008?

Yes, you can wrap only the hood or the roof of a Peugeot 3008, and mirror caps are another small option. These partial wraps use much less film than a full wrap and are good for a first project. Chrome delete is also a partial job that covers the window trim and badges, not the painted panels. Paint protection film on the front end is another way to wrap part of the car while keeping the original color visible.

Is a Peugeot 3008 hard to wrap?

A Peugeot 3008 is not hard to wrap, but some parts add work. Every trim has parking sensors in the bumpers, so the film is cut around each sensor circle. Some trims have cameras in the body, and the film is cut around each lens to keep the view clear. The tailgate has the rear glass in it, and the film ends at the edge of the glass, which needs careful trimming. The newest body is 178.8 in (4,542 mm) long, so a full wrap takes more film and labor than a smaller car.